Search

   (716) 893-6510

  [email protected]

75+ Years of Experience

No products in the wishlist.

Menu
Search

Return to Previous Page
Zoom images

SPX Power Team Hydraulic Jacking Systems

Spec Sheet
Inquire About This Product

Add to Wishlist
Category:
Description

Buffalo Hydraulic BHCSY1220X2-6.00-SPL

SPX Power Team PE4004 Electric Hydraulic Pump

  • 208/230/460 VAC, 3 Ph., 60 Hz., 10 Hp.
  • High capacity 2-Stage design delivers 420 cu.” per minute @10,000 psi.
  • 20 Gallons oil reservoir
  • 3-Position (Advance-Hold-Retract) manually operated directional valve.
  • 492 Lbs.

SPX Power Team RC12206C High-Tonnage Hydraulic Jacking Cylinders

  • 1,220 Lbs. Force- Each @9,898 psi (Maximum Pressure).
  • Single acting – load return.
  • 20.20″ Collapsed height.
  • 6.00″ Stroke/travel.
  • 2,116 Lbs. Each.
Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “SPX Power Team Hydraulic Jacking Systems”

Related Products

BVA Hydraulics – Buffalo Hydraulic High Tonnage Hydraulic Jacking Systems

BVA Hydraulics PEW1505T 10,000 psi  Electric-Hydraulic Pump 115 VAC, 60 Hz., 1 Ph., 1.5 Hp. Internal bypass relief valve – 10,000 p.s.i. (Maximum Pressure). 3...

BVA Hydraulics – Buffalo Hydraulic High Tonnage Hydraulic Jacking Cylinders

BVA Hydraulics H3008 Hydraulic Jacking Cylinders 30 Tons capacity – each @9,244 psi (Maximum Pressure). 15.24″ Collapsed Height. 8.27″ Stroke/Travel. Single acting, spring return. 100’s...

SPX Power Team Hydraulic Jacking Systems

SPX Power Team High-Pressure Hydraulic Pump & Cylinder Sets P-59 High-Pressure Hydraulic Hand Pump Internal relief valve – 10,000 psi Maximum pressure. High displacement 2-stage...

Buffalo Hydraulic Custom Hydraulic Jacking Cylinders

Buffalo Hydraulic BHDAJC-3.00X20.00-SPL Custom design hydraulic jacking cylinders. 3.00″ Diameter bore. 20.00″ Stroke/travel. Load holding over center valves for added safety & control. These custom...

BVA Hydraulics High Pressure, 20-Port, Electric Hydraulic Jacking System Console

BVA Hydraulics, Custom High-Pressure, 20-Port, Electric Hydraulic Jacking System Console 10,000 P.S.I. Maximum pressure. 20 Working ports allowing finite pressure and flow control and N.I.S.T....

Buffalo Hydraulic Weldment Straightening Press

Buffalo Hydraulic BHEHP06X12-SPL, Electric-Hydraulic Straightening Press Custom electric hydraulic press. Six pressing points offering 10.00″ of stroke/travel. 10,000 Lbs. force at each point. Independently controlled....

Buffalo Hydraulic Custom Hydraulic Pressing System

Buffalo Hydraulic BHEHP10X8.00-SPL. Custom Electric Hydraulic Press 115 VAC, 2-stage electric hydraulic pump. 3 Position, solenoid-operated directional valve. Hand-held, push button pendant (Advance-Hold-Retract). Adjustable pressure...

Buffalo Hydraulic Hydraulic Lift Tables

Buffalo Hydraulic BHLTFP2000-SPL Hydraulic Lift Table 24.00″ X 36.00″ Table Dimension. 2,000 Lbs. Capacity. 16.00″ Retracted height – 28.00″ Maximum Height. 4-Post design for added...
Flange Mount Hydraulic Cylinder

Buffalo Hydraulic Custom Flange Mount Cylinders

With the ability to easily adapt to varying mounting,operational and cycling requirements, this custom hydraulic cylinder design can be adapted to meet your requirements.
Placeholder

BVA Hydraulics – Buffalo Hydraulic High Tonnage Hydraulic Jacking Cylinders

BVA Hydraulics – Buffalo Hydraulic High Tonnage Hydraulic Jacking Cylinders BVA Hydraulics HL10002 Low Profile Jacking Cylinder 98.20 Tons capacity – each @10,000 p.s.i. (Maximum...

buffalo-hydraulic-white

The passion and drive for our company along with the customers we serve originated in 1948 when Leo Phillips began selling & servicing hydraulic equipment.  Launched with a focus on supporting the local Western New York industry, Buffalo Hydraulic was founded.

Buffalo, NY 14211
Email: [email protected]
Phone: (716) 893-6510

USEFUL LINKS

RECENT PRODUCTS

SPX Power Team, PE184 Vanguard Jr. Series, Electric-Hydraulic Pump

Buffalo Hydraulic proudly serves as a Platinum Distributor as well as a Factory Authorized Warranty Service Center for SPX Power Team - Hydraulic Technologies hydraulic products.

“Power Team” is a registered trademark of the SPX FLOW Hydraulic Technologies division of SPX FLOW Inc. (“SPX FLOW”). All Power Team products and parts, with the exceptions noted below, are warranted against defects in materials and workmanship for the life of the product or part. (The life of the product or part is defined as that point in time when it no longer safely or properly functions due to normal wear). Chains, batteries, electric motors, gas engines, knives and cutter blades which are sold with Power Team products are not covered by this warranty and instead are warranted as follows: • Electronics are warranted against defects in materials and workmanship for a period of one year from date of purchase. • Consumable parts or accessories, including without limitation, chains, batteries, knives and cutter blades are warranted against defects in materials and workmanship for a period of one year from date of purchase. • All electric motors and gas engines are separately warranted by their respective manufacturer under the terms and conditions stated in their separate warranty. The foregoing warranties do not cover ordinary wear and tear or any product or part that has been worn out, abused, heated, ground or otherwise altered, used for a purpose other than that for which it was intended or used in a manner inconsistent with any instructions regarding its use. To qualify for warranty consideration, return the Power Team product, freight prepaid, to a Power Team authorized repair center or to the SPX FLOW factory. If any product or part manufactured by SPX FLOW found to be defective by SPX FLOW, in its sole judgment, SPX FLOW will, at its option, either repair or replace such defective product or part and return it via best ground transportation, freight prepaid. THIS REMEDY SHALL BE THE EXCLUSIVE REMEDY AVAILABLE FOR ANY DEFECTS IN THE PRODUCTS OR PARTS MANUFACTURED AND SOLD BY SPX FLOW OR FOR DAMAGES RESULTING FROM ANY OTHER CAUSE WHATSOEVER, INCLUDING WITHOUT LIMITATION, SPX FLOW’S NEGLIGENCE. SPX FLOW SHALL NOT, IN ANY EVENT, BE LIABLE TO ANY BUYER FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES OF ANY KIND, WHETHER FOR DEFECTIVE OR NON-CONFORMING GOODS, NEGLIGENCE, ON THE BASIS OF STRICT LIABILITY OR FOR ANY OTHER REASON. SPX FLOW’s PowerThonTM Warranty is expressly limited to persons who purchase Power Team products or parts for the resale or for use in the ordinary course of the buyer’s business. THIS WARRANTY IS EXCLUSIVE, AND SPX FLOW MAKES NO OTHER WARRANTY OF ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, WITH RESPECT TO THE PRODUCTS MANUFACTURED AND SOLD BY IT, WHETHER AS TO MERCHANT-ABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ANY OTHER MATTER. No agent, employee, or representative of SPX FLOW has any authority to bind SPX FLOW to any affirmation, representation, or warranty concerning Power Team products or parts, except as stated herein. The purpose of this exclusive remedy shall be to provide the buyer with repair or replacement of products or parts manufactured by SPX FLOW found to be defective in materials or workmanship or negligently manufactured. This exclusive remedy shall not be deemed to have failed of its essential purpose so long as SPX FLOW is willing and able to replace said defective products or parts in the prescribed manner. Any inconsistent terms contained in SPX FLOW’s Standard Terms and Conditions, or other SPX FLOW terms or warranty documents, shall not be interpreted to modify or limit this PowerThonTM Warranty. For the avoidance of doubt, this PowerThonTM Warranty is applicable only to Power Team products and does not apply to any other SPX FLOW products.

Buffalo Hydraulic Custom-Design, Double-Acting, Flange Mount Pressing Cylinders

Buffalo Hydraulic Custom-Design, Double-Acting, Flange Mount Pressing Cylinders 3,00 psi maximum pressure. Double-acting, flange-mount design. 84,823 lbs. (42.4T) each at 3,000 p.s.i. ø6.00″ Internal bore....
,

BVA Hydraulics HLNF20002 Low Profile, Lock-Nut Design 200T Jacking Cylinder

Buffalo Hydraulic proudly serves as a Factory Authorized Stocking Distributor as well as a Factory Authorized Warranty/Service Center for all BVA Hydraulics products. ASME B30.1 BVA Hydraulics hydraulic cylinders are designed, built, and tested to meet or exceed ASME B30.1 standards. ISO 9001 Quality Assurance BVA Hydraulics products are manufactured through an International Quality Assurance System, ISO 9001, involving consistent oversight of administration, management, manufacturing, and production control.  Under this system, the related operations are monitored on all aspects from the purchase order to the assembly line and through to shipping the order. BVA Limited Lifetime Warranty All BVA Hydraulics products are warranted to be free of defects in materials and workmanship.  Any BVA product that does not conform to specification will be repaired or credited (at BVA’s option) at BVA’s expense for the life of the product.  Contact BVA or Buffalo Hydraulic for the disposition of this warranty. This warranty does not cover ordinary wear and tear, abuse, misuse, alteration, or use of improper fluids or maintenance as determined by BVA and its authorized service centers.  All electric motors, gas engines, batteries, and other parts or materials sold with or part of BVA products but are separately warranted by another manufacturer, are covered by that manufacturer’s warranty and not the BVA Lifetime Warranty.  BVA shall not be liable for consequential or incidental damage or loss.

© 2016 Buffalo Hydraulics. All Rights Reserved. Buffalo NY Web Design by Newbird

Terms and Conditions